一、木地板表面不平，怎么辦?
主要原因是基層不平或地板條變形起拱所致。在安裝施工時，應用水平尺對龍骨表面找平，如果不平應墊墊木調整。龍骨上應做通風小槽。板邊距墻面應留出10 毫米的通風縫隙。保溫隔音層材料必須干燥，防止術地板受潮后起拱。木地板表面平整度誤差應在 1 毫米以內。
二、木地板不小心浸水了怎么辦?
這要看是什么地板和進水量多少，一般來說極少量進水根本就不用管，地板都有一定的防潮功能，如果大量進水最好用吸塵器(干濕兩用那種)吸干，然后用風扇吹干。復合地板一般有較強的防浸水功能，實木地板也看廠家和質量，可以打電話到廠家咨詢。
三、新安裝的實木地板個別地方踩上去會響怎么辦?
①產生原因：看發出的聲音是怎么響，如果某個地方踩一腳響一下，再踩再響，連續如此，那肯定是木地龍與地面木榫之間沒有固定住，或者木榫材質太軟不吃力，被地龍拉起來所至;若是某個地方踩上去有時會有聲音，有時沒有，這種狀況大多是地板釘小于實木地板的鉆頭孔之故，地板雌雄槽之間有松動的空隙造成的。
②根治辦法：要徹底根治有一個辦法，重新緊固地龍，重裝地板，可是這樣費工又費料。只有在安裝地龍和地板之前，注重以下工藝和方法，地板才不會出聲：安裝地龍前一般都用 12 毫米的電錘鉆頭打孔，木榫起碼要 18~20 毫米以上的方形木榫夯實才有用，不能很輕松就打下孔去，過幾天木榫一干燥收縮就松了。夯地的木榫材質要比地龍材質硬，木材硬收縮力小，地龍就不容易把木榫彈拉上來，才能保持穩固性。有的一個房間地面水平高差好幾公分，這時木匠師傅在地龍下面會墊一些刀形木塞或三夾板之類，保證地龍水平，要注意墊高 2.5 厘米以上的地龍之間，必須要打上短地龍相互固定，防止地龍左右搖晃擺動，以保證地龍平整牢固。
四、地磚干鋪方法怎么做?
干鋪方法不易空鼓。步驟如下在原土建地面封膠，再用水泥調砂至半干狀態(用手抓成團狀)鋪在原土建水泥上，與原土建水泥成一體。然后把磚平放在半干水泥上用海綿捶打，把水泥中的氣泡擠壓出來。磚后背批濕水泥鋪在干水泥上，2小時內水泥凝固，這樣磚就與地面合成一體不會空鼓。
五、地面大面積鋪地毯，鋪完后起鼓怎么辦?
除地毯在鋪裝前未鋪展平外，主要原因是鋪裝時撐子張平松緊不勻及倒刺板中個別倒刺沒有抓住所致。如地毯打開時，出現鼓起現象，應將地毯反過來卷一下后，再鋪展平整。鋪裝時撐子用力要均勻，張平后立即裝入倒刺板，用扁鏟敲打，保證所有倒刺都能抓住地毯。
